-
Posts
224 -
Joined
-
Last visited
Content Type
Profiles
Forums
Store
Gallery
Events
Local Fish Stores
FAQ
Blogs
Downloads
Posts posted by Wildman926
-
-
Sale Pending
-
PM response sent
-
-
-
Lowered price, light and driver only -$275
-
PM Sent
-
As title states, like new. Strip is 6 months old, dimmer is 4 months old.
I purchased one too many strips, so one has got to go. I paid $455 for this setup, so save some money here.
This strip is extremely bright. I could not take a pic directly at it, as they warn you not to look directly at it.
$350 firm, no trades.
-
The problem is with the solder that connects the two 12" strips. You have to remove the silicone, use a soldering iron with a little flux and wet the tip of the soldering iron with solder, and reflow the joint connection. Then recover the removed silicone with clear silicone. What happens, is they heat up and there is not enough solder from the factory, and the connection starts to open up, which causes the remaining lights past that joint to either dim, or go out all together.
I still have the strips for sale, just not the blue 453nm ones.
- 1
-
-
I would like the "Green Sinularia - M - $15"
-
PM on Tyree toadstool
-
453nm strips sold.
-
Hello Ty,
I will take the Broken yellow scroll coral pieces $5, Unknown Chalice $10, and large LPS colony $10. I will send paypal, and can grab early next week if ok with you.
-
Question.. I'm new around here so if I were to manage to get the money to get some lights off you, what would I need to power them? (total noob over here)
Just plug in the power supply. You can see the power supply in the first post, the first pic, with the strips laying under normal light. These could not be any easier to use.
-
Here is a sample of the lights in use -
36" - 2 12k, 1 453nm, 1 Fusion
-
I am also selling the 453nm strips that I have.
2 - 48" $100 each
2 - 36" $75 each
The 48" strips have been repaired. There is a factory default with the units that will show bad solder joints if they exist. The bad solder joint will show up after they get to normal operating temperature. The strips are in 1' lengths. The bad solder joint will dim or put out the rest of the length of the strip. I have removed the silicone over the bad joints, reflowed the solder joint, and refilled the clear silicone. They work as new as seen on pics. The lights come with power supplies to power up a pair of strips.
48" strips -
36" strips -
-
I have for sale several strips -
2 - 48" 12000k 30w
2 - 36" 12000k 30w
1 - 48" "Fusion" 2:1 12000k:453nm ratio of led
1 - 36" "Fusion" 2:1 12000k:453nm ratio of led
48" - $100 each
36" - $75 each
I am asking half of what they cost new, and these lights were run only 4 hours a day. I have power supplies to light up each pair. I used these on my LPS 150g and my 90g softie tanks for 2 years, with great success, and have pics to show. I want to go to sps, so I bought some BML lights for more power.
In the pics, the left and middle pair are the 12000k. The right pair is the Fusion. I can deliver next week when I am in Austin, or can ship at buyers expense. Thank you very much!
-
Does this chalice look familiar to anyone? My pic is not the best, and I will try to get another one, but it is a deep green, with an orange ring around the edge. It has different colored mouths, some orange, some blue, and it now has light green metallic specs in it. It has grown like crazy in the 6 months I had gotten it. It is currently 4" in diameter, and it was only 2" when I got it. Got it on a trade.
-
Hello Ken,
What is the chalice in pic number 2?
-
PM on the duncan
-
I will take the BML lights if still available. Thanks.
-
-
Thank you sir! I will see you tomorrow.
BTW - THIS is a large Hollywood Stunner Chalice -
-
Text sent on toadstool, Hollywood chalice, and lettuce coral.
Looking for 200g skimmer
in Want to Buy
Posted
I have an Aquamaxx EM300 if interested. Like new, was my backup due to being a bit large for my 150g, but still pulled skim hard.
It comes with an extra new impeller. The impeller in the pump looks new also.
I have made two modifications -
1. Plumbed airline into cup to pull moist air in to keep venturi clean, and put it up above the top line so that it does not pull in waste.
2. Added extra air nozzle to run ozone directly into the venturi. It is capped
off.
PM me if interested.